Auger and Pile Driver Inclinometers and Levels
Augers and pile drivers have the same general requirement, to keep the head vertical so that the pile is properly installed and provide the structural support required from it. Our sensors and displays can help the operator setup the machine correctly and ensure it stays on track throughout the operation. Our products have been designed to withstand the harshness of this environment and we can provide off the shelf or customised solutions to meet most application requirements.
Vertical Alignment
Most piles or foundation bore holes need to be drilled vertically. Often the machine and boom carrying the Auger will not be level, so there is some control required to ensure it is vertical prior to drilling, and that it remains vertical during drilling or piling. We have a range of sensors that can be used to measure this, and also cab mounted display systems to help the operator control the process. The electronic sensors can also interface with the machines control system to enable automated adjustment. We have a range of tough and reliable products that can meet the needs of this application.
Products
- Inclinometer Sensors
DAS, LCH-A-D, MAS-2, SOLAR-2 - Digital Displays
PDTS, IDS - Circular Levels
AVF100 series, CG Series, 5229 series
Angular Alignment and GNSS Compensation
Some foundations are installed at a specific angles to take loads in directions other than the vertical. In this case it is necessary to know the pitch and roll angle of the head of the machine so the drilling angle can be properly set and controlled. Providing information about the angle of the head to the machine control system it is also possible to calculate the location of the head in the ground relative to the GNSS position of the cab mounted receiver. We have a range of tough and reliable sensors and displays that can be used in this application, and can provide customised and integrated solutions where required.
Products
- Inclinometer Sensors
LCH-A-D, MAS-2, SOLAR-2 - Digital Displays
PDTS, IDS
Inclinometer Sensors
| Teilenr. | Bild | Größe (LxWxH mm) |
Anzahl der Achsen | Bereich (°) |
Art des Ausgangs | Auflösung (°) | Genauigkeit (°) (20°C) |
Speisespannung Min. - Max. (V) |
Schutzart |
|---|---|---|---|---|---|---|---|---|---|
| MAS-2-45-1-CANJ |   |
44x41x12.5 | 2 | ±45 | CAN J1939 | 0.02 | 0.3 | 6.5 - 36 | IP67 & IP69K |
| MAS-2-30-1-CANJ | |
44x41x12.5 | 2 | ±30 | CAN J1939 | 0.02 | 0.2 | 6.5 - 36 | IP67 & IP69K |
| MAS-2-15-1-CANJ | |
44x41x12.5 | 2 | ±15 | CAN J1939 | 0.02 | 0.1 | 6.5 - 36 | IP67 & IP69K |
| MAS-2-45-2-CANJ | |
44x41x12.5 | 2 | ±45 | CAN J1939 | 0.02 | 0.3 | 6.5 - 36 | IP67 & IP69K |
| MAS-2-30-2-CANJ | |
44x41x12.5 | 2 | ±30 | CAN J1939 | 0.02 | 0.2 | 6.5 - 36 | IP67 & IP69K |
| MAS-2-15-2-CANJ | |
44x41x12.5 | 2 | ±15 | CAN J1939 | 0.02 | 0.1 | 6.5 - 36 | IP67 & IP69K |
Digital Inclinometers
| Teilenr. | Bild | Anzahl an Achsen |
Bereich (°) |
Display Ausgabe |
Auflösung (°) |
Genauigkeit (°) (20°C) |
Stromquelle | Sensorgröße (LxWxH mm) |
Displaygröße (LxWxH mm) |
Sensor-Schutzart | Display-Schutzart |
|---|---|---|---|---|---|---|---|---|---|---|---|
| IDS-SOLAR2 |   |
2 | ±30 | RS232 | 0.001 | ±0.030° | Internal Li-Po Battery, or external | 75x37.5x15 | 130x72x26.5 | IP67 | IP67 |
| IDS |   |
2 | RS232 | Interner Li-Po-Akku. oder externer | - | 130x72x26.5 | - | IP67 | |||
| PDTS-SOLAR2-01 |   |
2 | ±30 | 2 x SPCO Relay and USB | 0.001 | ±0.030 | Externe Gleichstromversorgung | 75x37.5x15 | 72x72x23.5 | IP67 | IP65 (when panel mounted) |
| PDTS-SOLAR2 | |
2 | ±30 | 2 x SPCO Relay and USB | 0.001 | ±0.030 | Externe Gleichstromversorgung | 75x37.5x15 | 72x72x23.5 | IP67 | IP65 (when panel mounted) |
| PDTS |   |
2 | 2 x SPCO Relay and USB | Externe Gleichstromversorgung | 72x72x19.4 | IP65 (when panel mounted) |
